Asante NetStacker Hub Manuel d'utilisateur

NetStacker II Dual Speed Stackable Hub User’s Manual SHBBook Page 1 Wednesday, March 3, 1999 8:03 PM

Introduction Page 1-2 The NetStacker II 12 port unmanaged hub provides 12 twisted pair ports. The 24 port managed hub provides 24 twisted pair ports.

Performance Features Page 1-3 Each hub features full plug-and-play installation. LED indicators include power status, port link activity status, coll

Introduction Page 1-4 SHBBook Page 4 Wednesday, March 3, 1999 8:03 PM

Page 2-1 2Installation This chapter describes the components and explains how to install, mount, and apply power to your NetStacker II dual speed hu

Installation Page 2-2 The front panel of the 24 port hub displays: ❑ Twenty-four dual speed (UTP) Ethernet ports ❑ One uplink switch button ❑ LED ind

Components Page 2-3 Figure 2-3 LED Indicators on 12 port hub Rear Panels of the 12 Port and 24 Port Hubs The rear panels of the 12 port and 24 port

Installation Page 2-4 Cabling and Voltage Requirements This section describes the cabling and voltage requirements for the NetStacker II 12 port and

Placement and Mounting Page 2-5 Placement and Mounting This section describes how to mount the NetStacker II on a desktop or shelf. Hub Location The

InstallationPage 2-63 Place the device into the 19-inch rack and attach it firmly.Ensure that the ventilation holes do not get blocked.Figure 2-6 Rac

Connecting Network DevicesPage 2-7Figure 2-7 Connecting cable to a NIC◆ Note: The maximum length of a cable between a hub and a device is 100 meters

Copyright NoticeTrademarks Asanté Technologies and FriendlyNET are trademarks of Asanté Technologies, Inc. Ethernet is a registered trademark of the

InstallationPage 2-82 Make sure that the length of the straight through cable between the NetStacker II and a 100Mbps repeater does not exceed 5 meter

Connecting Network DevicesPage 2-9Figure 2-9 Connecting to another hub using Uplink PortStraight through cableButton pressed in123456789101112MIIMod

InstallationPage 2-10Stacking Hubs Up to eight NetStacker II hubs may be connected within a stack. Furthermore, a management module can be installed e

Connecting Network DevicesPage 2-11Adding Fiber Optic Connectivity via MIITo add connectivity for 100Base-FX transmission media, insert the optional M

InstallationPage 2-12Powering on the HubThe NetStacker II hub may be turned on with (or without) LAN segment cables connected.To power on the hub:1 Co

Page 3-13LED IndicatorsThis chapter explains how to interpret the front panel LED indicators on NetStacker II dual speed hubs. There are no LEDs on th

LED IndicatorsPage 3-2Figure 3-2 24 port hub LEDsPower LED The Power LED is green and should always be lit when the NetStacker II is in use. After p

Hub ID Number LEDsPage 3-3Hub ID Number LEDsThe Hub ID LEDs are a numbered row of eight green LEDs. If your NetStacker II hub is configured with other

LED IndicatorsPage 3-4SHBBook Page 4 Wednesday, March 3, 1999 8:03 PM

Page A-1ATroubleshootingTable A-1 describes how to troubleshoot problems with your network and/or the Switch by monitoring the Switch’s LEDs. Table A-

Page i Table of Contents About This Manual ... iiiChapter Contents ...

Page A-2SHBBook Page 2 Wednesday, March 3, 1999 8:03 PM

Page B-1BSpecificationsNetStacker II Hub SpecificationsStandard IEEE 802.3 Ethernet standardIEEE 802.3u Fast Ethernet standardInterfaces RJ-45 (TP)

Page B-2SHBBook Page 2 Wednesday, March 3, 1999 8:03 PM

Page C-1CTechnical SupportContacting Technical SupportTo contact Asanté Technical Support:Telephone (800) 622-7464Fax (801) 566-3787Fax-Back (800) 741

SHBBook Page 2 Wednesday, March 3, 1999 8:03 PM

SHBBook Page 1 Wednesday, March 3, 1999 8:03 PM

ASANTÉ TECHNOLOGIES, INC., 821 FOX LANE, SAN JOSE, CA 95131PHONE: 800.622.7464 • FAX: 801.566.3787 • e-mail address: [email protected] •World Wide Web

Page ii LED Indicators ...3-1Power LED ...3-2Co

Page iii About This Manual This manual describes the NetStacker II dual speed stackable hubs. The manual focuses on the following two models: ❑ 12-po

Page iv Document Conventions This manual uses the term “NetStacker II” to refer to the 12 port and 24 port dual speed hubs, and “hub” to refer to all

About This Manual Page -v 11. If an extension cord is used with this product, make sure that the total ampere ratings on the products connected to th

Page vi SHBBook Page vi Wednesday, March 3, 1999 8:03 PM

Page 1-1 1Introduction This chapter introduces the Asanté NetStacker II 12 port and 24 port dual speed stackable hubs and provides an overview of bas