Asante 10Base2 Manuel d'utilisateur

Mini MAUInstallation Guide

Mini MAU Page 7 Installation Mini MAU The installation of an Asanté Mini MAU is very simple: 1 Locate the AUI port on the device.The AUI is on the r

Mini MAU Page 8 Figure 2 Mini MAU for Thin Ethernet AUI connection(15-pin)BNC connectionSix LEDsSwitches minimau Page 8 Monday, August 26, 1996

Mini MAU Page 9 Thin cable (10Base2) with Mini MAU Connect the 10Base2 Mini MAU to the device’s AUI port. Before the 10Base2 Mini MAU is connected

Mini MAU Page 10 Figure 3 Mini MAU for Fiber AUI connection(15-pin)Fiber connectionSix LEDsSwitchesFiber connection minimau Page 10 Monday, Aug

Mini MAU Page 11 Fiber Connect the 10BaseFL Mini MAU to the device’s AUI port. Connect the Mini MAU fiber connector to the fiber cable with ST connect

Mini MAU Page 12 LEDs and Switches for the Mini MAU Mini 10BaseT MAU LED Display LED Color Status Power on Green MAU ONreceiving power from AUILi

Mini MAU Page 13 Switches for 10BaseT MAU There are three switches on the side on the 10BaseT Mini MAU.The default settings for the switches are ide

Mini MAU Page 14 ❖ Note: If the MAU is used with a hub or repeater this switch should be disabled. ❖ Link Integrity Enabled Test Switch This switch

Mini MAU Page 15 Figure 4 Mini MAU Fiber to hubHubAUI connection(15-pin)10 Base F MAUFiber connector10 Base F network minimau Page 15 Monday, A

Mini MAU Page 16 Mini 10BaseFL MAU LED Color Status Power on Green MAU ONreceiving power from AUILink Green ON Link OKOFF Link failedReceive Green O

Copyright Notice Copyright 1993 by Asanté Technologies, Inc.All rights reserved. No part of this manual, or any associated artwork, software, product

Mini MAU Page 17 Switches for 10Base-F MAU The default settings are identified below: ❏ Loopback Test Switch enabled.(1, switch UP) ❏ HBE Switch disa

Mini MAU Page 18 Figure 5 Mini MAU Thin Ethernet to MacintoshMacintoshMini MAU 10Base2Thin Ethernet networkAUI connectorFive LEDs minimau Page 1

Mini MAU Page 19 Mini 10Base2 MAU LED Color Status Power ON Green MAU ONreceiving power from AUIHBE ON Green ON HBE is ONSwitch set to “Down” (0) po

Mini MAU Page 20 Switches for 10Base2 MAU The default settings are identified below: ❏ Termination disabled (1, switch UP) ❏ HBE disabled (1, switch

Mini MAU Page 21 ❖ Note : All Asanté MAUS attached to a hub or repeater should have HBE disabled. For example, if the Mini MAU is attached to an As

Mini MAU Page 223 Insert the Mini MAU by hand-guiding it into its recessed slot until the MAU is securely fas-tened to it’s connector.4 Re-insert the

Mini MAU Page 23Specifications Mini MAUPower❏ 120mA@ 11-16VDC from the Ethernet device AUI.Environmental❏ 1 to 50 CDimensions❏ 3.35”x 1.65” x 0.8”minim

Technologies, Inc. for a Returned Merchandise Authorization (RMA) number, that (2) you clearly write the RMA number on the outside of the package, an

Mini MAU Page 1 Introduction Thank you for purchasing a Mini MAU from Asanté Technologies.The Asanté Mini MAU is an ideal network solution for conne

Mini MAU Page 2 Asking for assistance To contact Asanté Technical Support for help: Technical Support Hours 6:00 AM to 6:00 PM Pacific Standard Time,

Mini MAU Page 3 Product OverviewAsanté Mini MAUs The Asanté Mini MAU plugs directly onto the back of your PC, Macintosh or any other network device

Mini MAU Page 4 Summary of Mini MAU Features • Standards based transceivers for unshielded twisted pair (UTP), thin and fiber-optic Ethernet.• Full c

Mini MAU Page 5 Mini MAU Media and Connectors Mini MAU Media Connector Port10BaseT Mini MAU UTPUnshieldedTwisted PairRJ-45 AUI 10BaseFLMini MAU

Mini MAU Page 6 Figure 1 Mini MAU for 10BaseTAUI connection(15-pin)RJ-45 connectionSix LEDsSwitches minimau Page 6 Monday, August 26, 1996 11: